Home » Exterior Care » Exterior Trim/ Lenses

 Checkout
Product ID: 1217
Lake Country Professional Plastic Restoration System
Free Shipping on Orders Over $150 (Before Taxes)
Lake Country Professional Plastic Restoration System
  (Enlarge)  

Use the same kit that the pros use to restore plastic surfaces to like new condition!

The Plastic Pro - Professional Plastic Restoration System from Lake Country smoothes and restores complete optical clarity to all plastic surfaces. This step-by-step scratch and defect removal system removes swirls, fine scratches, stains and oxidation, and polishes the plastic to restore and maintain optical clarity.


Lake Country’s Professional Plastic Restoration System utilizes the most technologically advanced plastic polishes, compounds, pads and techniques. Originally developed for the aviation industry, this plastic restoration kit has can be used on virtually all non-porous surfaces.
 

The Professional Plastic Restoration System is for use on the following surfaces:

  • All Plastics
  • Acrylics
  • Plexiglas, Colored & Non-colored
  • All Polycarbonate Surfaces, Windows & Fairings
  • Lexan
  • Gel Coats
  • Fiberglass
  • Marine & RV Plastics
  • Bathtub Fixtures
  • Swimming Pool Accessories
  • Cycles
  • Fairings
  • Home Appliances
  • Vinyl Floors
  • Countertops
  • Crafted Wood Furniture
  • Kitchen and Bath

    The Professional Plastic Restoration System works with circular polishers and with air, electric and cordless power drills. In just a few minutes plastic surfaces can be polished and restored to like new condition. This kit includes one 4 oz. Heavy-Cut Plastic Polish, one 4oz. Light-Cut Plastic Polish, one 4oz. Polish, one 4oz. Final Polish, one 3 7/8” rotary backing plate, one drill adapter, one 3.5 Inch Orange CCS Foam Cutting Pad and one 3.5 Inch White CCS Foam Polishing Pad.

    4 oz. Step 1 Heavy-Cut Plastic Polish
    Fast-cutting abrasives suspended in a thick, lubricating polishing lotion remove 600 grit or finer scratches. Heavy-Cut Polish leaves a medium gloss and prepares the surface for further polishing. Use with Orange CCS Foam Cutting Pad.

    4oz. Step 2 Light-Cut Plastic Polish
    Fine abrasives and cleaners remove 800-2000 grit or finer scratches, hairline scratches, paint and overspray stains and produces a high gloss finish. Use with Orange CCS Foam Cutting Pad.

    4oz. Step 3 Polish
    Ultra-fine abrasives and mild cleaners restore a very high gloss to plastic surfaces. Remove 2000 grit or finer scratches, fine hairline scratches and swirls. Use with White CCS Foam Polishing Pad.

    4 oz. Step 4 Final Polish
    Achieve a high gloss finish, remove very fine swirls and restore optical clarity with Final Polish. Use on a regular basis for routine maintenance to keep plastic surfaces looking new. Use with Orange CCS Foam Cutting Pad.

    3 7/8 inch rotary backing plate
    This backing plate screws directly onto a rotary polisher, such as the Makita 9227C. Hook and loop system enables foam pads to attach to the backing plate.

    Drill Adapter
    Use this adapter to use the included backing plate on your air, electric or cordless drill.

    3.5 Inch Orange CCS Foam Cutting Pad
    Use for cutting and removal of deeper imperfections. Primarily used with PP-1, PP-2 and removal of 600 grit sanding marks.

    3.5 Inch White CCS Foam Polishing Pad
    Used for high gloss polishing and swirl removal. Primarily used with PP-3 and PP-4 polishes.

    Please Note: The Professional Plastic Restoration System is for machine use. Applying these products by hand will not produce satisfactory results.

    Depending upon the severity of the defect in the surface of the plastic that you are working on, you may elect to work with light abrasive wet sand papers to remove deep imperfections prior to polishing with the Professional Plastic Restoration System. Over-aggressive use of wet sand papers will quickly remove material and possibly create a weakness or distortion in the surface.

    The Professional Plastic Restoration System has the ability to removing 600 grit and finer sanding marks.

    Please note: This kit is not intended to remove large chips or nicks in plastic. Damaged areas may be repaired if substructure has not been penetrated.

    For best results, clean and dry foam pads between each step.

    Chips, very deep scratches and gouges : Begin with step #1. Deep scratches: Begin with step #2. Minor scratches: Begin with step #2. If scratch persists, you may choose to wet sand very lightly with water-soaked 600 grit wet sand paper and then repeat step #2. Hairline scratches: Begin with step #3 Swirls: Begin with step #5

    Before you begin, clean the area that you will be working on with plastic cleaner and a microfiber towel to remove dirt and other loose contaminants.

    1. Presoak wet sandpaper in a solution of non-alkyd-soap and warm water. Start with 320 grit and proceed to 400 grit and 600 grit respectively. Sand in straight lines only and inspect the surface often as you work. Your goal is to remove the surface defect while removing he least amount of base material possible. (Please note: Sanding is an optional step for severely scratched lens covers. The sandpaper is not included in this kit.)
    2. Spread a small amount of PP-1 Heavy-Cut over an approximately 1 sq. ft. area using the orange cutting pad. Polish surface for about three minutes, only using the weight of the machine without applying any additional pressure. Polish in perpendicular motions (up and down, back and forth). Repeat as necessary until defect or sanding marks are removed.
    3. Clean surface thoroughly with plastic cleaner and a microfiber towel. Spread a small amount of PP-2 Light-Cut over an approximately 1 sq. ft. area using the orange cutting pad. Polish surface for about three minutes, only using the weight of the machine without applying any additional pressure. Polish in perpendicular motions (up and down, back and forth). Repeat as necessary until previous polishing pattern has been removed.
    4. Clean surface thoroughly with plastic cleaner and a microfiber towel. Spread a small amount of PP-2 Light-Cut over an approximately 1 sq. ft. area using the white polishing pad. Polish surface for about three minutes, only using the weight of the machine without applying any additional pressure. Polish in perpendicular motions (up and down, back and forth). Repeat as necessary until previous polishing pattern has been removed.
    5. Clean surface thoroughly with plastic cleaner and a microfiber towel. Spread a small amount of PP-3 Polish over an approximately 1 sq. ft. area using the white polishing pad. Polish surface for about three minutes, only using the weight of the machine without applying any additional pressure. Polish in perpendicular motions (up and down, back and forth). Repeat as necessary until previous polishing pattern has been removed.
    6. Clean surface thoroughly with plastic cleaner and a microfiber towel. Spread a small amount of PP-4 Final Polish over an approximately 1 sq. ft. area using the white polishing pad. Polish surface for about three minutes, only using the weight of the machine without applying any additional pressure. Polish in perpendicular motions (up and down, back and forth). Repeat as necessary until previous polishing pattern has been removed.
    7. For continued maintenance and removal of light swirls, halos and fine scratches, repeat step #6.

      The Professional Plastic Restoration System gives you the tools and the techniques to polish, smooth and restore optical clarity to plastic surfaces. This kit contains enough material to restore approximately 9,000 sq. inches of plastic surface!

      Kit includes:
      1 - 4 oz. PP-1 Heavy Cut
      1 - 4 oz. PP-2 Light-Cut
      1 - 4 oz. PP-3 Polish
      1 - 4 oz. PP-4 Final Polish
      1 - 3 7/8” rotary backing plate
      1 - Drill adapter
      1 - 3.5 Inch Orange CCS Foam Cutting Pad
      1 - 3.5 Inch White CCS Foam Polishing Pad
       
 
 
Price: Cdn$54.99

 

 
Product Reviews

No Reviews For This Product.

Click to review this product


Newsletter Sign-up



 More Info